Differences

This shows you the differences between two versions of the page.

--- hardware:mould [2020/06/25 13:34] – [SNMP Hints] himuser
+++ hardware:mould [2022/01/14 18:44] (current) – external edit 127.0.0.1
@@ Line 102: / Line 102: @@
   * Full Access via SSH:
     * ''ssh pi@mould-control.emp.him.uni-mainz.de'' with raspberry as password
-==== Controlling loop ====
-There is temperature ramp prepared which controls the heating power of all four heaters between 0 and 100% depending on the Temperatur read on C1.
-Run inside a screen session:
-  /home/pi/python/actor/actor.py
-Code can be found here: https://gitlab.rlp.net/bes3-mainz/mogon-testbench/snippets/497
-==== Bare metal controlling of the heaters ====
-HINT: Better use the web interface to get the status and set the heaters power: http://localhost:10001/status.php#page1
-Control the heaters be writing them a value in the range ''0.00'' and ''1.00'':
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer<Dimmer ID 1..4>/set' -m <brightness 0..1.0>
-Example:
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer4/set' -m 0.75
-Get the status
-  mosquitto_sub -h mould-control -t 'homie/fsrcontrol/heater/dimmer1' -t 'homie/fsrcontrol/heater/dimmer2' -t 'homie/fsrcontrol/heater/dimmer3' -t 'homie/fsrcontrol/heater/dimmer4' -v
-Switch on all 4 heaters:
-<code bash>
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer1/set' -m 1;
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer2/set' -m 1;
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer3/set' -m 1;
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer4/set' -m 1;
-  echo "done"
-</code>
-Switch off all 4 heaters:
-<code bash>
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer1/set' -m 0;
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer2/set' -m 0;
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer3/set' -m 0;
-  mosquitto_pub -h mould-control -t 'homie/fsrcontrol/heater/dimmer4/set' -m 0;
-  echo "done"
-</code>
 ===== New slowcontrol with Node Red =====
@@ Line 160: / Line 122: @@
 Source code:
+  * 21.7.2020:   * {{ :hardware:mould:flows-20200731.json.zip |Selector for Heaters added}}
+  * 13.7.2020: {{ :hardware:mould:flows-20200713.json.zip |Displayed State Names changed}}
   * 17.6.2020: {{ :hardware:mould:flows.json.zip |}}
   * {{ :hardware:mould:flows-20200622.json.zip |22.6.2020}}
+  * {{ :hardware:mould:flows_20200625_with_multiplug.json.zip |25.6.2020 with multiplug}}
 ==== external set point to the oven ====
@@ Line 174: / Line 139: @@
 ==== SNMP Hints ====
-To set and get info from the Brennstuhl multiplug run the following commands:
+To set and get info from the Brennstuhl multiplug (IP address 10.106.11.21) run the following commands:
 Copy the MIB file into ~/.snmp/mibs/nbs.mib . In case an error is stated, change ''ws_brs'' to ''wsbrs'' in the mib file.
 The use the MIB file, add
-  -m ALL
+<code bash>
-to all your commands. BUT note: the mib file seems to be a bit buggy.
+  -m ALL
+</code>
+to all your commands. BUT note: the mib file seems to be a bit buggy. To get the ISO numbers, eg add ''-m none''.
 Perform a complete walk of all parameters