Differences

This shows you the differences between two versions of the page.

--- beamtimes:2022_apr:a1 [2022/04/20 14:43] – himuser
+++ beamtimes:2022_apr:a1 [2022/04/21 15:16] (current) – himuser
@@ Line 2: / Line 2: @@
 ==== Change Target ====
-* Make sure the beam is off! Usually one moves the target only while being on the phone to MAMI.
+  * Make sure the beam is off! Usually one moves the target only while being on the phone to MAMI.
-* Open a terminal as mezzo on control1
+  * Open a terminal as mezzo on control1
-* Optional: Check the target position with where_target
+  * Optional: Check the target position with ''where_target''
-* Go to the new position with the appropriate go-command (e.g. go_C12)
+  * Go to the new position with the appropriate go-command (e.g. ''go_C12'')
-* Check the target position with where_target. The setpoint should be the selected target, and the difference should be small ( < 100 )
+  * Check the target position with ''where_target''. The setpoint should be the selected target, and the difference should be small ( < 100 )
 === Checking Beam Position ===
+  * Call MAMI and tell them, that you want to check the beam position.
-* Call MAMI and tell them, that you want to check the beam position.
+  * **Ask MAMI to switch off the beam and wait for the confirmation, that the beam is off!**
-* '''Ask MAMI to switch off the beam and wait for the confirmation, that the beam is off!'''
+  * Move in the screen (see section: **Change Target**) ''go_Al2O3''
-* Move in the screen (see section: ''Moving the Target'')
+  * on a1analyse (Computer with Dual screen) locate the upwards arrow on the panel next to the a1-logo
-* on a1analyse (Computer with Dual screen) locate the upwards arrow on the panel next to the a1-logo
+    * Click it to open the menu
-** Click it to open the menu
+    * Select the menu item ''Target Camera''
-** Select the menu item ''Target Camera''
+    * An MPlayer window will open. If not, check if it's already open.
-** An MPlayer window will open. If not, check if it's already open.
+  * Press ''c'' to activate the camera, now you should see the cross hairs on the screen.
-* Press 'c' to activate the camera, now you should see the cross hairs on the screen.
+  * Ask MAMI for a little bit of beam (nanoamperes)
-* Ask MAMI for a little bit of beam (nanoamperes)
+  * When you see the beam on the screen, take a picture by pressing ''p''. It will be saved to the logbook.
-* When you see the beam on the screen, take a picture by pressing 'p'. It will be saved to the logbook.
+  * Ask MAMI to center the beam on the target and take another picture.
-* Ask MAMI to center the beam on the target and take another picture.
+  * **Switch off the camera** by pressing ''c'' again. Close the MPlayer window.
-* '''Switch off the camera by pressing 'c' again.''' Close the MPlayer window.
+  * **Ask MAMI to switch off the beam and wait for the confirmation, that the beam is off!**
-* '''Ask MAMI to switch off the beam and wait for the confirmation, that the beam is off!'''
+  * Move in the correct production target (e.g. ''go_C12'')
-* Move in the correct production target (e.g. ''go_C12'')
+  * Wait for the target to reach the position.
-* Wait for the target to reach the position.
+  * Check the target position with ''where_target''. The setpoint should be the selected target, and the difference should be small ( < 100 ).
-* Check the target position with ''where_target''. The setpoint should be the selected target, and the difference should be small ( < 100 ).
+  * Ask MAMI for the correct beam current.
-* Ask MAMI for the correct beam current.
 ==== Spec A ====